Analisis Pengaruh Temperatur Saat Pengadukan Resin Terhadap Sifat Mekanik Polylactic Acid Plus
| dc.contributor.author | Kusyairi, Harris Al | |
| dc.date.accessioned | 2026-09-24T21:27:51Z | |
| dc.date.issued | 2025-05-19 | |
| dc.description | Dr. Eng. Ilhamdi, S.T., M. Eng.; Afid Nugroho, S.T., M. Eng. | |
| dc.description.abstract | Material Polylactic Acid Plus (PLA+) dikenal sebagai salah satu material yang sering digunakan dalam teknologi pencetakan 3D karena memiliki kelebihan sebagai bahan yang biodegradable dan sifat mekaniknya yang baik serta kemudahan dalam pengolahannya. Namun, daya tahannya terhadap beban lentur masih perlu ditingkatkan untuk aplikasi struktural seperti pesawat nirawak. Penelitian ini bertujuan menganalisis pengaruh variasi temperatur pengadukan resin terhadap sifat mekanik PLA+ yang dilapisi resin epoksi menggunakan metode dip coating dan menentukan resin yang terbaik untuk pengaplikasian coating pada PLA+ berdasarkan sifat mekanik khususnya sifat bending yang meliputi flexural strength (Kekuatan lentur) dan modulus elastisitas. Dua jenis resin epoksi yang digunakan yaitu Bisphenol A-Epichlorohydrin (BPAE) dan Bisphenol A Diglycidyl Ether (DGEBA). Variasi temperatur pengadukan adalah 30°C, 50°C, dan 70°C. Resin dicampur harderner dengan perbandingan 2:1, diaduk pada 300 rpm selama 3 menit, lalu dilakukan dip coating pada spesimen PLA+ yang telah dicetak dengan desain mengikuti standar ASTM D790. Setelah dikeringkan selama 48 jam, spesimen diuji dengan metode three-point bending sesuai dengan standar desain. Hasil penelitian menunjukkan bahwa resin DGEBA memberikan performa lebih baik dibandingkan BPA-E. Pada temperatur pengadukan 30°C didapat kekuatan lentur tertinggi sebesar 85,18 MPa, dengan modulus elastisitas 2,9 GPa dan beban maksimum 255,44 N. Namun, peningkatan temperatur pengadukan hingga 70°C menyebabkan penurunan kekuatan lentur dan modulus elastisitas meskipun beban maksimum meningkat hingga 301,72 N. Sebaliknya, spesimen dengan resin BPAE menunjukkan tren penurunan signifikan pada kekuatan lentur dan modulus elastisitas seiring dengan meningkatnya temperatur pengadukan resin. Temperatur pengadukan berpengaruh signifikan terhadap sifat mekanik PLA+ yang dilapisi resin epoksi, dan resin DGEBA lebih unggul dalam meningkatkan kekuatan lentur dibandingkan BPA-E. | |
| dc.identifier.uri | https://ailib.my.id/handle/123456789/50345 | |
| dc.language.iso | id | |
| dc.publisher | Universitas Andalas | |
| dc.subject | PLA+ | |
| dc.subject | Dip Coating | |
| dc.subject | Sifat Mekanik | |
| dc.subject | Uji Bending | |
| dc.subject | Pengadukan Resin | |
| dc.subject.classification | TJ Mechanical engineering and machinery | |
| dc.title | Analisis Pengaruh Temperatur Saat Pengadukan Resin Terhadap Sifat Mekanik Polylactic Acid Plus | |
| dc.type | Thesis | |
| dcterms.dateSubmitted | 2025-06-03 | |
| dcterms.references | S. A. M. Tofail, E. P. Koumoulos, A. Bandyopadhyay, S. Bose, L. O’Donoghue, and C. Charitidis, "Additive manufacturing: Scientific and technological challenges, market uptake and opportunities," Materials Today, vol. 21, pp. 22–23, 2018. Z. Kurnia, "Implementasi Teknologi 3D Printing dalam Berbagai Industri," KMTech.ID, [Online]. Available: https://www.kmtech.id/post/implementasi-teknologi-3d-printing-dalam-berbagai-industri . [Accessed: Sep. 16, 2024]. eSUN, "PLA PRO (PLA+) Filament," [Online]. Available: https://www.esun3d.com/id/pla-pro-product/. [Accessed: Nov. 11, 2024]. Carbiolice, "What is PLA Bioplastic?," [Online]. Available: https://www.carbiolice.com/en/news/pla-bioplastic-2/. [Accessed: Nov. 7, 2024]. M. Eryildiz, "Estimation of three-point bending behavior using finite element method for 3D-printed polymeric sandwich structures with honeycomb and reentrant core," European Mechanical Science, vol. 6, pp. 196–200, Sep. 2022, doi: 10.26701/ems.1101832. P. Nguyen-Tri, T. A. Nguyen, P. Carriere, and C. Ngo Xuan, "Nanocomposite coatings: Preparation, characterization, properties, and applications," International Journal of Corrosion, vol. 2018, Article ID 4749501, pp. 1–19, Feb. 2018, doi: 10.1155/2018/4749501. D. Kumar, D. K. Samal, S. Biswas, and M. K. Kar, "Toughening of petroleum-based (DGEBA) epoxy resins with various renewable resources-based flexible aliphatic polyols," Materials Today: Proceedings, vol. 5, pp. 18398–18408, 2018, doi: 10.1016/j.matpr.2018.06.142. S. Sudarisman, S. P. Singh, and R. R. Salim, "Tensile and flexural properties of bamboo fiber-epoxy green composites under wet and dry conditions," Advanced Materials Research, vol. 1125, pp. 136–141, 2015, doi: 10.4028/www.scientific.net/AMR.1125.136. Monchy, "Bisphenol A epoxy resin," [Online]. Available: https://monchy.com/products/bisphenol-a-epoxy-resin/ . [Accessed: Nov. 22, 2024]. J. Huang, P. Fu, W. Li, L. Xiao, J. Chen, and X. Nie, "Influence of crosslinking density on the mechanical and thermal properties of plant oil-based epoxy resin," RSC Advances, 2022, doi: 10.1039/D2RA04206A. A. Nourbakhsh and A. Ashori, "Fundamental studies on wood–plastic composites: Effects of fiber concentration and mixing temperature on the mechanical properties of poplar/PP composite," Polymer Composites, vol. 29, no. 5, pp. 569–573, 2008, doi: 10.1002/pc.20578. H. Tondi, "Rancang Bangun Mesin Ekstruder Filamen 3D Printer," Skripsi, Fakultas Teknologi Industri, Universitas Islam Indonesia, 2019. M. R. Yanhar and D. Musryady, "Kuat Tarik, Modulus Elastisitas, dan Makrostruktur Komposit Serat Alam dengan Partikel Rumput Teki (Cyperus Rotundus) sebagai Penguat," Semnastek UISU, pp. 65–70, 2019. J. Cantrell et al., "Experimental characterization of the mechanical properties of 3D-printed ABS and polycarbonate parts," in Proceedings of the 2016 Annual Conference on Experimental and Applied Mechanics, pp. 89–105, 2017. E. Pollet, Environmental Silicate Nano-Biocomposites, 2006, doi: 10.2174/97816080528511060101. C. J. Brinker and G. W. Scherer, Sol-Gel Science: The Physics and Chemistry of Sol-Gel Processing, Academic Press, 1990. A. Sánchez-Herencia, "Water based colloidal processing of ceramic laminates," Key Engineering Materials, vol. 333, pp. 39–48, Mar. 2007, doi: 10.4028/www.scientific.net/KEM.333.39. Biolin Scientific, "Dip coating: Quick Way to Nanoparticle Films," [Online]. Available: https://www.biolinscientific.com/blog/dip-coating-quick-way-to-nanoparticle-films. [Accessed: Nov. 8, 2024]. L. Zhang, C. Zhang, and X. Liu, "Recent advancements in dip-coating for thin films," Materials Science, vol. 48, no. 2, pp. 110–123, 2015. S. Pang, C. Lin, and Y. Zhu, "Epoxy resin coatings for enhanced mechanical properties in polymer-based composites," Composites Science and Technology, vol. 186, pp. 107–114, 2020. Shandong Tianshuo Chemical, "Bisphenol A Epichlorohydrin," [Online]. Available: https://www.shandongtianshuoid.com/info/bisphenol-a-epichlorohydrin-90253083.html . [Accessed: Nov. 22, 2024]. Z. Bulinski, Numerical Modelling and Credibility Analysis of Free Surface Flows in Selected Industrial Processes, Master's thesis, 2010. National Center for Biotechnology Information, "Epoxy resins based on Bisphenol A Diglycidyl Ether," [Online]. Available: https://www.ncbi.nlm.nih.gov/books/NBK499000/ . [Accessed: Nov. 23, 2024]. K. Bogaerts, A. Lavrenova, A. Spoelstra, N. Boyard, and B. Goderis, "Curing kinetics and morphology of a nanovesicular epoxy/stearyl-block-poly(ethylene oxide) surfactant system," Soft Matter, vol. 11, Jun. 2015, doi: 10.1039/C5SM01051A. Rudawska, "Epoxy adhesives," in Handbook of Adhesion Technology, 3rd ed., pp. 415–442, 2017, doi: 10.1201/9781315120942. Amaral, R. Rodriguez, F. Garcia, L. Junior, and E. Carvalho, "Impact of aliphatic amine comonomers on DGEBA epoxy network properties," Polymer Engineering and Science, vol. 54, no. 9, pp. 2132–2138, 2013, doi: 10.1002/pen. ASTM International, "Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials," ASTM D790-00, West Conshohocken, PA, USA, 2000. M. B. Uctasli, H. D. Arisu, L. V. J. Lassila, and P. K. Vallittu, "Effect of preheating on the mechanical properties of resin composites," European Journal of Dentistry, vol. 2, pp. 263–268, Oct. 2008. D. W. Widyatmaja, W. W. Raharjo, and H. Sukanto, "Pengaruh suhu pencampuran terhadap kekuatan tarik dan fracture toughness epoxy resin–organoclay montmorillonite nanokomposit," Mekanika: Majalah Ilmiah Mekanika, vol. 12, no. 2, pp. 101–107, Mar. 2014. D. O. Saputra, F. Setiawan, and D. Wicaksono, "Pengaruh variasi suhu mixing resin pada uji tarik pada material komposit serat fiberglass dengan metode Vacuum Assisted Resin Infusion (VARI)," Teknika STTKD: Jurnal Teknik, Elektronik, Engine, vol. 9, no. 1, pp. 129–137, Jul. 2023, doi: 10.56521/teknika.v9i1.868. "Pentingnya Kalibrasi UTM untuk Keakuratan Pengujian Material," Balai Besar Logam dan Mesin (BBLM), [Online]. Available: https://www.bblm.go.id/pentingnya-kalibrasi-utm-untuk-keakuratan-pengujian-material/ . [Accessed: Nov. 25, 2024]. "C-MAG HS 7 Magnetic Stirrers," IKA, [Online]. Available: https://www.ika.com/id/Products-LabEq/Magnetic-Stirrers-pg188/C-MAG-HS-7-3581200/ . [Accessed: Nov. 25, 2024]. | |
| local.eprints.dir | disk0/00/49/57/69 | |
| local.eprints.division | 07E | |
| local.eprints.id | 495769 | |
| local.eprints.type | thesis/2Sarjana | |
| local.eprints.uri | http://scholar.unand.ac.id/495769/ | |
| local.fakultas | Fakultas Teknik | |
| local.identifier.nim | 1810911019 | |
| local.prodi | S1 Teknik Mesin | |
| local.thesis.level | Skripsi |
